Customer Service
22274775
BISON Max Repair Extreme Adhesive 8g
BISON Max Repair Extreme Adhesive 8g
Extremely strong & flexible
Water-resistant, UV resistant & Temperature resistant
Dishwasher-safe
Resistant to shock and vibrations
Solvent-free, Transparent
Instruction to Use:
Take care that the surfaces to be bonded are clean, dry and free of dust and grease. Apply the adhesive on one side. Press the parts against each other. Adjustments can be made within 5 minutes. The maximum final bonding strength is reached after approximately 24 hours.
Advice: Loosen the stuck cap under the hot tap and remove any hardened adhesive in the tube cap with a sharp knife. After use, let some adhesive come out of the tube before you screw the cap on it.
Storage conditions:
Store in a dry, cool, frost-free place.
Technical specifications
Other specifications
Warranty
months
Length
cm
Width
cm
Height
cm
Weight
kg
Information on technical characteristics, the delivery set, compatibility, the country of manufacture and the appearance of the goods is for reference only and is based on the latest information available at the time of publication.
Related Products
-
BISON Montagekit Super Strength Tube Card 125 gram
Very high final bond strength
Can be used internally and externally
Easy to apply
Suitable for joining non-porous materials together
Universally applicable
Suitable for uneven surfaces
Water-resistant & Temperature resistant
Instruction to Use:
Depending on the weight of the material, apply the adhesive evenly in vertical stripes or dots at intervals of between 20 and 40 cm. Always apply adhesive to the corners and along the edges. Assemble ma...
Availability: In Stock
1.750 KWD
-
BISON Kit All Purpose Contact Adhesive 140 mL
Bonds immediately
Super-strong
Suitable for materials under stress
Universal
Liquid
Moisture and frost resistantSimple to use
Resistant to temperatures between -40°C and +70°C
Instruction to Use:
Parts must be clean, dry and free of grease. Coat both substrates completely. Allow drying for a minimum of 10-40 minutes. In case of porous materials, apply a second coat and let dry. Then join parts and roll or tap firmly (with a rubber mallet).
...
Availability: In Stock
1.500 KWD
-
BISON Plastic Blister 25 mL
Colorless
Solid
Waterproof
Instruction to Use:
Not to be applied at temperatures below +5°C.
Apply a thin layer of adhesive and join parts almost directly, in any case, while glue layer is still moist. Remove excess glue immediately.
Storage conditions:
Store in a dry, cool and frost-free place.
...
Availability: In Stock
1.250 KWD
-
BISON Kit Transparent 50ml
Crystal clear
Bonds immediately
Super-strong & Simple to use
Suitable for materials under stress
Moisture and frost resistant
Instruction to Use:
Apply the adhesive thinly and evenly to both surfaces using the fine-toothed adhesive spreader (1 mm) or brush. Allow both surfaces to dry for 10 to 25 minutes. As soon as the adhesive stops stringing, join parts. Adjustment is then no longer possible. Avoid entrapping of air bubbles. Firmly tap, roll or press materials.
Po...
Availability: In Stock
1.000 KWD
-
BISON Vinyl Plastic Blister 25 mL
Transparent
Waterproof
Flexible
Instruction to Use:
Not to be applied at temperatures below +10°C.
When gluing overlapping parts: Apply glue thinly to the entire surface of both sides. Let dry for 5-20 minutes. The glue should be dry to the touch. Drying time depends on the nature of materials and on temperature. Join parts and press or tap firmly. After joining, parts stick immediately! Final bond strength depends on pressure, therefore exercise as much ...
Availability: In Stock
1.750 KWD
-
BISON Glass Blister 2 mL
Fast & Waterproof
UV-curing
Transparent, crystal clear
Dishwasher resistant
Instruction to Use:
Apply glue outside influence of (bright) sunlight thinly on one side. Press parts firmly for 10-20 seconds and place in direct sunlight. Do not move parts while curing. BISON Glass cures under the influence of UV rays (sunlight). Bonding can only be effectuated in direct sunlight. It is possible to use a UV-lamp with awavelength between 250 nm to 350 nm.
Points of attention...
Availability: In Stock
2.250 KWD
-
BISON Spray Adhesive 2 In 1 Aerosol 500 mL
For temporary and permanent fixation
Easy to use
Fast and strong
Moisture resistant
Instruction to Use:
Shake aerosol spray can well prior to use.
Rock-solid bond: Immediate fixation: Apply adhesive to both sides. Allow to dry for at least 10 minutes, join parts and press or tap. No adjustments are possible. Adjustable fixation: It is also possible to apply adhesive to one side and join the parts immediately. Adjustments are possible within 5 minutes...
Availability: In Stock
3.500 KWD
-
BISON Super Wood Glue 75g (BIS-6305289)
Water-resistant (EN 204 D3)
Stronger than wood
Ideal for internal and external applications
Transparent when dry
Paintable, Solvent-free
Instruction to Use (Preliminary surface treatment) :
Apply the adhesive with a brush or some other tool in an even and thin layer on one or both parts. Let penetrate for a few minutes, the assemble the parts and clamp or press for 30-60 minutes. The desired pressure is 2-5 kg/cm².
The ambient temperature, the adhe...
Availability: In Stock
1.000 KWD
-
BISON Kit All Purpose Contact Adhesive 650 mL
Bonds immediately
Super-strong
Suitable for materials under stress
Universal
Liquid
Moisture and frost resistantSimple to use
Resistant to temperatures between -40°C and +70°C
Instruction to Use:
Parts must be clean, dry and free of grease. Coat both substrates completely. Allow drying for a minimum of 10-40 minutes. In case of porous materials, apply a second coat and let dry. Then join parts and roll or tap firmly (with a rubber mallet)....
Availability: In Stock
2.000 KWD
-
BISON Kit All Purpose Contact Adhesive 3L
Bonds immediately
Super-strong
Suitable for materials under stress
Universal
Liquid
Moisture and frost resistantSimple to use
Resistant to temperatures between -40°C and +70°C
Instruction to Use:
Parts must be clean, dry and free of grease. Coat both substrates completely. Allow drying for a minimum of 10-40 minutes. In case of porous materials, apply a second coat and let dry. Then join parts and roll or tap firmly (with a rubber mallet).
Poi...
Availability: In Stock
8.800 KWD